How to Install LAMZU PTFE Skates on MAYA, Inca and Atlantis OG V2
By Official LAMZU Gaming Gear | Wireless Gaming Mouse ... | Published: 2026-10-13
Category: How-to Guides
A step-by-step guide to replacing worn PTFE feet on LAMZU MAYA, Inca, and Atlantis OG V2 mice, with checkpoints to avoid common mistakes and keep your glide smooth.
Quick answer
To install LAMZU PTFE skates, first remove the old feet with a plastic tool and clean the base with isopropyl alcohol. Then peel the backing from the new skates, align them with the recessed areas, and press firmly for 30 seconds. Let the mouse sit for a few hours before use to let the adhesive cure. Use the correct replacement set for your model: MAYA, Inca, or Atlantis OG V2.
Tools and preparation
Gather a plastic spudger or an old credit card, isopropyl alcohol (90% or higher), lint-free cloth or cotton swabs, and the replacement skates for your specific LAMZU model. Work on a clean, well-lit surface to avoid losing small parts. If your mouse has a dustproof seal, check its condition and replace it if worn, as a damaged seal can let debris under the skates and cause scratchiness.
Remove the old skates
Slide the plastic tool under one edge of each skate and gently pry upward. Work slowly to avoid bending the mouse base or scratching the surface. If the adhesive resists, apply a small amount of isopropyl alcohol to the edge and wait a few seconds. Never use metal tools, as they can gouge the plastic and create high spots that affect glide.
Clean the base
After removal, wipe the base with isopropyl alcohol to remove all adhesive residue and oils. Use a lint-free cloth or cotton swab and let it dry completely. Any leftover residue will prevent the new skates from sitting flush, leading to inconsistent glide and early wear.
Install the new skates
Peel the protective backing from one skate at a time. Align the skate with the recessed area on the mouse base, then press down firmly for 30 seconds. For the Atlantis OG V2, the Big size option covers a broader surface area, which can provide a more stable glide. Ensure the edges are fully seated and not overlapping the mouse edge.
Break-in and testing
After installation, let the mouse rest for a few hours to allow the adhesive to cure fully. Then test the glide on your mousepad. You may notice a slightly different feel initially; this is normal as the PTFE settles. If the glide feels uneven, check that all skates are flat and properly aligned. Avoid using the mouse on rough or dirty surfaces, as this can damage the skates.
Step-by-step installation with checkpoints
- Remove old skates: Use a plastic tool to gently pry up each skate. Apply isopropyl alcohol if the adhesive is stubborn. Avoid metal tools to prevent scratches. Checkpoint: The base should be free of residue and smooth to the touch.
- Clean the base: Wipe the base with isopropyl alcohol and a lint-free cloth. Let it dry completely before proceeding. Checkpoint: No oily or sticky spots remain; the surface is dry.
- Align and press new skates: Peel the backing and align each skate with its recess. Press firmly for 30 seconds, ensuring edges are flush. Checkpoint: Skates sit flat and do not overhang the mouse edges.
- Cure and test: Let the mouse rest for a few hours, then test glide on your mousepad. If uneven, press down again or check alignment. Checkpoint: The mouse glides smoothly without scratching or wobbling.
Compatible LAMZU replacement skates
- LAMZU Atlantis OG V2 Mouse PTFE Skates (Big): Genuine LAMZU replacement skates for the Atlantis OG V2 mouse, made from PTFE (Teflon) material for a smooth, durable glide, available in a Big size option for broader surface coverage. The Big size provides more surface area, which can suit players who prefer a more controlled, stable glide.
- LAMZU Inca Mouse PTFE Skates: The LAMZU Inca Mouse PTFE Skates are compatible with LAMZU Inca mice as replacement feet and are made from PTFE for a smooth, low-friction surface. These are the correct fit for the Inca model, ensuring proper alignment and performance.
- LAMZU MAYA Mouse PTFE Skates: Genuine LAMZU accessory for the MAYA mouse, made from PTFE material for low-friction performance and available in White to match your setup. The MAYA-specific cut ensures a precise fit, and the White color can complement a white mouse or setup.
