How to Pair LAMZU MAYA X with 8K Dongle
By Official LAMZU Gaming Gear | Wireless Gaming Mouse ... | Published: 2026-10-17
Category: How-to Guides
Learn how to pair your LAMZU MAYA X with the 8K dongle for a stable 8000Hz wireless connection. Follow these simple steps to get your mouse and dongle communicating correctly.
Quick answer
To pair your LAMZU MAYA X with the 8K dongle, plug the dongle into your PC, insert the mouse USB cable into the mouse, then press the pairing button on the dongle and the mouse simultaneously. The process takes about 10 seconds and ensures a stable 8000Hz wireless connection.
What you need before starting
Before you begin, make sure you have the LAMZU MAYA X mouse and a compatible 8K dongle — either the LAMZU MAYA X 8K Dongle (designed specifically for the MAYA X) or the standard LAMZU 8K Dongle. Both support 8000Hz polling, but the MAYA X 8K Dongle is color-matched to your mouse in Black or White. You'll also need the USB cable that came with your mouse, a PC with a free USB port, and about two minutes of uninterrupted time.
If you are using the standard LAMZU 8K Dongle, verify that your MAYA X firmware supports it. The MAYA X 8K Dongle is plug-and-play with the MAYA X, while the standard dongle may require a firmware update on the mouse. Check LAMZU's support page for the latest firmware if you experience pairing issues.
Common pairing pitfalls
The most common mistake is skipping the cable connection step. The MAYA X must be connected to your PC via the USB cable during pairing — the dongle cannot pair wirelessly on its own. Another frequent issue is pressing the pairing buttons too quickly or not holding them long enough. Press and hold each button for about 3 seconds until the LED indicators flash rapidly.
If pairing fails, try moving the dongle to a different USB port (preferably USB 3.0) and ensure no other wireless devices are interfering. Restart both the mouse and the dongle by unplugging and replugging them. If the LED on the dongle stays solid after a few seconds, the pairing was successful.
Step-by-step pairing process
- Connect the dongle to your PC: Plug the 8K dongle into an available USB port on your computer. Use a USB 3.0 port for best performance and to ensure the 8000Hz polling rate is supported. Checkpoint: The dongle LED should light up. If it doesn't, try a different USB port.
- Connect the mouse via USB cable: Use the provided USB cable to connect the LAMZU MAYA X directly to your PC. This powers the mouse and enables the pairing mode. Do not skip this step — the mouse cannot pair wirelessly on its own. Common mistake: Forgetting to plug in the cable. The mouse will not enter pairing mode without a wired connection.
- Press the pairing button on the dongle: Locate the small pairing button on the side of the dongle (near the LED). Press and hold it for about 3 seconds until the LED starts blinking rapidly. This indicates the dongle is searching for a device. Checkpoint: If the LED does not blink, release and press again. A solid LED means it is already paired.
- Press the pairing button on the mouse: On the bottom of the LAMZU MAYA X, find the pairing button (usually near the sensor). Press and hold it for about 3 seconds. The mouse LED will start blinking rapidly to indicate it is in pairing mode. Common mistake: Pressing the button too briefly. Hold for a full 3 seconds until the LED blinks.
- Wait for the connection to establish: Keep both devices within a few feet of each other. Within 5-10 seconds, the dongle LED should change from blinking to a steady solid light, indicating a successful pairing. The mouse is now ready for 8000Hz wireless use. Troubleshooting: If the LED stays blinking after 15 seconds, unplug the dongle and mouse, restart your PC, and repeat steps 1-4.
Dongle options for your MAYA X
- LAMZU MAYA X 8K Dongle: The LAMZU MAYA X 8K Dongle is a dedicated accessory designed to pair with compatible LAMZU devices for a high-performance wireless connection. Offered in Black and White color options, this dongle complements your setup with a clean, minimal look. Compatible with LAMZU MAYA X devices for a seamless wireless experience. Supports 8K polling rate for ultra-fast response times during intense gaming sessions. Choosing the MAYA X 8K Dongle guarantees full compatibility and a color-matched look, and it supports the full 8000Hz polling rate without any additional setup steps.
- LAMZU 8K Dongle: The LAMZU 8K Dongle is a wireless accessory designed to pair with compatible LAMZU devices. This dongle enables a high-performance 8K connection, making it a suitable addition for users seeking a responsive setup. It is available in a clean White color option to match a variety of setups. The standard LAMZU 8K Dongle works with multiple LAMZU devices, but you may need to update the MAYA X firmware first. It is a good backup or multi-device option if you already own one.
